4.8. Sharpen (Unsharp Mask)

4.8.1. Visão Geral

Figura 17.44. Exemplo de aplicação do filtro Aguçar

Exemplo de aplicação do filtro Aguçar

A imagem original

Exemplo de aplicação do filtro Aguçar

Filtro Aguçar aplicado


Out-of-focus photographs and most digitized images often need a sharpness correction. This is due to the digitizing process that has to divide a color continuum in points with slightly different colors. Elements smaller than the sampling frequency will be averaged into a uniform color. So sharp borders will be rendered a little blurred. The same phenomenon appears when printing color dots on paper.

The Sharpen filter (previously called Unsharp Mask) sharpens edges of the elements without increasing noise or blemish. It is the king of the sharpen filters.

[Dica] Dica

Some imaging devices like digital cameras or scanners offer to sharpen the created images for you. We strongly recommend you disable this means of sharpening and use GIMP filters instead. This way you regain the full control over the sharpening of your images.

To prevent color distortion while sharpening, you can Decompose your image to HSV and work only on Value. Go to ColorsComponentsDecompose.... Make sure the Decompose to Layers box is checked. Choose HSV and click OK. You will get a new gray-level image with three layers, one for Hue, one for Saturation, and one for Value. (Close the original image so you won't get confused). Select the Value layer and apply your sharpening to it. When you are done, with that same layer selected, reverse the process by using Compose. Go to ColorsComponentsCompose.... Again choose HSV and click OK. You will get back your original image except that it will have been sharpened in the Value component.

4.8.2. Ativando o filtro

You can find this filter through FiltersEnhanceSharpen (Unsharp Mask)….

4.8.3. Opções

Figura 17.45. Opções do filtro Aguçar

Opções do filtro “Aguçar”

Presets, Input Type, Clipping, Blending Options, Preview, Split view
[Nota] Nota

These options are described in Seção 2, “Common Features”.

Raio

The slider and input boxes (0.0-1500.0) allow you to set how many pixels on either side of an edge will be affected by sharpening. It is better to always sharpen an image at its final resolution.

Quantidade

This slider and input boxes (0.0-300.0) allow you to set the strength of sharpening.

Limiar

This slider and input boxes (0.0-1.0) allow you to set the minimum difference in pixel values that indicates an edge where sharpen must be applied. So you can protect areas of smooth tonal transition from sharpening, and avoid creation of blemishes in face, sky or water surface.

4.8.4. Como é que uma máscara de desaguçar funciona?

Usar uma máscara de desaguçar para tornar uma imagem mais aguçada, ou nítida pode parecer um pouco estranho. Aqui está a explicação:

Think of an image with a contrast in some place. The intensity curve of the pixels on a line going through this contrast will show an abrupt increase of intensity: like a stair if contrast is perfectly sharp (blue), like an S if there is some blur (yellow).

Now, we have an original image with some blur (black curve) we want to sharpen. We apply some more blur: the intensity variation will be more gradual (green curve).

Let us subtract the difference between blurredness intensity (green curve) and the intensity of the original image (black curve) to the intensity of the original image (black curve). We get the red curve, which is more abrupt: contrast and sharpness are increased. QED.

Unsharp mask was first used in silver photography. The photographer first creates a copy of the original negative by contact, on a film, placing a thin glass plate between both; that will produce a blurred copy because of light diffusion. Then both films are placed in a photo enlarger, to reproduce them on paper. The dark areas of the positive blurred film, opposed to the clear areas of the original negative will prevent light to go through and so will be subtracted from the light going through the original film.

Na fotografia digital, com o GIMP, se desejar reproduzir o efeito manualmente, você pode realizar os seguintes passos:

  1. Abra sua imagem e duplique-a ImagemDuplicar

  2. Na cópia, duplique a camada CamadaDuplicada camada, em seguida, desça o menu Filtros e aplique DesfocarDesfocagem Gaussiana para a camada duplicada com a opção padrão IIR e raio 5.

  3. In the layer dialog of the duplicated image, change Mode to Subtract, and in the right-click menu, select Merge down.

  4. Clique e arraste a única camada que você tem para a imagem original, onde ela aparece como uma nova camada.

  5. Altere o modo desta camada para Adição.

É isso aí. O plug-in Máscara de desaguçar faz o mesmo efeito para você.

No início da curva, você pode ver um mergulho. Se a desfocagem for significativa, este mergulho é muito profundo, o resultado da subtração pode ser negativo, criando uma lista de cor complementar aparecerá ao longo do contraste, ou uma auréola negra em torno de uma estrela no fundo claro de uma nebulosa (efeito de olho preto) .

Figura 17.46. O efeito de Olhos Preto

O efeito de “Olhos Preto”